providing a window into the process. Rev: n/a. P/N: n/a. ECO: n/a. Dynisco 1/8 DIN Indicator. Concise Product Manual Cleaning Tool Kit, Machining Tool Kit, Indicator , Process. Readout UPR , Process Controller ATC For additional options please contact the factory. For additional options please consult factory. Accessories. Indicator , Process Readout UPR, Process Controller ATC,. Cleaning Tool Kit, Machining.

Author: Brasho Mazragore
Country: Suriname
Language: English (Spanish)
Genre: Music
Published (Last): 15 October 2018
Pages: 60
PDF File Size: 2.36 Mb
ePub File Size: 18.20 Mb
ISBN: 860-7-66496-560-9
Downloads: 35233
Price: Free* [*Free Regsitration Required]
Uploader: Fesida

Repeat Steps 3 and 4 until 8 shifts have been performed. High voltage that may be present on leads can cause electrical shock.

Digital pressure indicator / for melt / process – PTE, PTE – Dynisco

U This parameter establishes the upper limit for the analog output; only the numerical value is shown during modification. The indicator automatically returns to the normal operating mode after 6 seconds if no changes are made.

Address Space The whole variables are addressable as word as well as bit; the user may choose the better way according to the condition. The two values dynixco be equal.

The decimal point dynosco the right of the display will be lit steadily. Press the FUNC key to initialize zero calibration. Monitoring Peak High and Peak Low By pressing while the measured value is displayed, it is possible to monitor the fynisco high value. All signals are optically isolated and the baud rate is adjustable between and baud.


The display only shows the number of counts for the digital to analog converter. Note that alarm defaults are High, Reverse Acting. The perform calibration press The display will show tA Followed by: Press FUNC to initiate the configuration procedure, starting at the first parameter.

dynisco 1390 3d models

The measure value is sent as: When using Dynisco transducers, the Shunt Calibration value should be set to The new values will be enabled but they will be lost when the instrument is powered down.

If necessary, you may now select the analog ouput calibration procedure by pressing Analog Dynisxo Calibration, below. You can select a voltage output of 0 – 5 Vdc or 0 – 10 Vdc or current outputs of 4 – 20 mA or 0 – 20 mA to drive chart recorders or data acquisition equipment. After reading, the word is set to 0 if the value read is 3 or 4.

Grizzly Bear 3D model. Programming the Alarm 2 set point is the same as Alarm 1 above, except that the display alternately shows 2. Repeat Step 3 another shift. ATV58E user manual in The word resets after reading.

FBX version Stem Cell compatible. Reading boolean variables as words: Full Scale Value and a numerical value from 10 to The oldest non sent alarm variations are lost Status alarm 1 Range: Two independent SPDT alarm relays are a standard feature of the Key items on the front panel are: A compact, dynusco mm x 96 mm 1.


Loc or UnLoc UnLoc. Continue doing this until all bytes have been processed.

Dynisco 1390 Indicator Series

Press the FUNC button to reach desired parameter then make output adjustments by pressing or until the signal output measured by the multimeter reaches the proper value. A digital filter to reduce the effects of input variations on the display, analog output and alarms. The external contact, if enabled, resets both alarms. Print Settings Printer Brand: It is the Users responsibility to provide an external fuse or circuit breaker.

A procedure for generating a CRC is: This function masks low alarm conditions during start-up until the measured cynisco first becomes greater than the alarm threshold plus hysteresis.

Textures, materials, light and renderer setup, cameras Dynisdo would indicate High alarm, automatic reset, reverse action. When this is done, a complete byte will have been processed. FUNC Default data will now be loaded.

An example of a C language function performing CRC generation is shown below. If applicable, connect alarm s.